0 1 2 3 4
看了还看

48V Volt LED Battery Indicator Meter Gauge Golf Cart for Standard Lead acid Battery

热销榜
  • 宝贝详情
  • Part No.: HMX-BM003ET

    UPC: 738770031862


    Notice:
    -Make sure your "C" terminal is either connected to the Battery "+" or a Key switch, Othersise, Meter will scan from full to empty then shuts off .
    -Meter will stay full position while first is connected with batteries and indicate the actual battery level after 155 seconds.
    -Please connect the correct voltage to your battery indicator as noted on your model . Failure to connect to the correct voltage will damage the batery indicator causing it to function abnormally.
    -Once battery was fully charged, Meter will cycle through for continuous 6 minutes then stay "full" position.
    -The Battery Meter works on Lead-acid Batteries only.

    Specifications:
    -The batteries voltage is displayed using a 10 segment LED bar graph(1 Red, 2 Yellow and 7 Green LEDs) display from full (far right green LED) to empty (far left red LED).
    -The second LED from the left flashes as a warning that the batteries voltage has been discharged to 80% of their capacity.
    -At a 90% battery discharge, the red and yellow LEDs will alternately flash to indicate a very low voltage capacity is remining.
    -It is strongly recommended to recharge the batteries when you get to the 3rd Yellow LED, this is a safety precaution to avoid dead batteries.
    -Operating and Storage Temperature: -20℃ to 85℃.
    -Accuracy: +/- 0.5 percent.
    -Net Weight: 21g / 0.8oz.

    Troubleshooting Tips
    1, Meter cannot move to full charge.
    This happens when battery was fully charged but the battery voltage cannot reach to preset fully charged voltage of meter, just disconnect the meter from power and reconnect, meter will reset to full.

    2, Meter scans from full to empty then shuts off:
    This occurs if your “C” terminal is not connected, make sure your “C” terminal is either connected to the battery + or a key switch.

    Part No.: HMX-BM003ET

    UPC: 738770031862


    Notice:
    -Make sure your "C" terminal is either connected to the Battery "+" or a Key switch, Othersise, Meter will scan from full to empty then shuts off .
    -Meter will stay full position while first is connected with batteries and indicate the actual battery level after 155 seconds.
    -Please connect the correct voltage to your battery indicator as noted on your model . Failure to connect to the correct voltage will damage the batery indicator causing it to function abnormally.
    -Once battery was fully charged, Meter will cycle through for continuous 6 minutes then stay "full" position.
    -The Battery Meter works on Lead-acid Batteries only.

    Specifications:
    -The batteries voltage is displayed using a 10 segment LED bar graph(1 Red, 2 Yellow and 7 Green LEDs) display from full (far right green LED) to empty (far left red LED).
    -The second LED from the left flashes as a warning that the batteries voltage has been discharged to 80% of their capacity.
    -At a 90% battery discharge, the red and yellow LEDs will alternately flash to indicate a very low voltage capacity is remining.
    -It is strongly recommended to recharge the batteries when you get to the 3rd Yellow LED, this is a safety precaution to avoid dead batteries.
    -Operating and Storage Temperature: -20℃ to 85℃.
    -Accuracy: +/- 0.5 percent.
    -Net Weight: 21g / 0.8oz.

    Troubleshooting Tips
    1, Meter cannot move to full charge.
    This happens when battery was fully charged but the battery voltage cannot reach to preset fully charged voltage of meter, just disconnect the meter from power and reconnect, meter will reset to full.

    2, Meter scans from full to empty then shuts off:
    This occurs if your “C” terminal is not connected, make sure your “C” terminal is either connected to the battery + or a key switch.